Just complete the form below and we'll contact you to answer any questions you have.
Many tins and cans contain hazardous waste such as oil or paint, the removal of which can be very expensive. The Mil-tek 2101 Can Crusher will reduce the volume of cans and tins by up to 90%, allowing you to reduce the amount of hazardous waste bins, the number of lifts required and, most importantly, reduce your costs by up to 80%.
The University of Mary Washington is a liberal arts and sciences university in Virginia. Their waste management partner Sodexo, opted for a Can Crusher to more easily transport and recycle food cans.
Hörby Paint Shop is an auto paint shop and bodywork shop in Sweden. The 101 Can Crusher reduces the cost of refuse and eliminates the need to rent a container.
Rosenlunds Vårdcentral is a hospital in central Stockholm. They use a hygienic 101 Can Crusher to reduce the volume of waste produced.
A Mil-tek technician will guide you through installation, which is done by simply connecting your 2101 Can Crusher to a compressed air supply. You are now ready to start minimizing.
Place an empty tin upright into the machine. The 2101 Can Crusher can handle cans, tins and drums up to 30 litres in size.
To activate, simply close the door and ensure the handle is pressed firmly down. This activates the pressing pate, which is released when the handle is lifted again.
Crushed cans take up 90% less space than filled cans, making them easy to store and transport for recycling.
All kinds - tins, cans, paint cans, oil drums, all kinds of hazardous and non/hazardous containers except pressurised aerosol cans.
No, the most important thing is that the cans are empty. However, to maximise the lifespan of your machine, we recommend rinsing cans in cold water before crushing.
The machine can stand either indoors or out - most important is that you place the machine so that you sort your waste at source. If you place the machine outside it must be under a roof. Be aware that cold weather conditions can influence the performance of the machine. Your Mil-tek consultant will help analysing the best place to install the machine.
As they are air-powered (pneumatic) rather than hydraulic, Mil-tek balers are extremely quiet (<70 dB). If you have an existing air-line you simply plug the machine and then your existing compressor acts as the engine. If you need to have a compressor installed, a Mil-tek technician will ensure that the compressor is placed at a distance from the machine and then install an air-hose between the compressor and the machine.
Many food products are packaged in metal tins and cans that, once empty, take up valuable space in bins. Using a Mil-tek 2101 Can Crusher to compact the used cans will reduce volume by 90%.
The Mil-tek 2101 Can Crusher is air-powered meaning that not only is it quiet, there is also no risk of oil contamination. These two key factors mean that it can safely be placed in a hygienic environment where food is prepared.
Empty paint and oil cans are full of air and take up unnecessary space in bins. A Mil-tek 2101 Can Crusher will reduce the volume of empty cans by 90% and can run from an existing air-line or a supplied compressor, reducing running costs and improving energy consumption. The high quality enamel finish also ensures the machine is not affected by hazardous liquid like paint or car oil.
The air powered Mil-tek 2101 Can Crusher is the ideal solution for compressing cans and metal food containers in the Hospital environment. The Mil-tek 2101 Can Crusher is air-powered meaning that not only is it quiet, there is also no risk of oil contamination. These two key factors mean that it can safely be placed in a hygienic environment where food is prepared.
| Height (mm) | 2005 |
| Width (mm) | 525 |
| Depth (mm) | 510 |
| Weight | 125 kg |
| Capacity | Cans: <30 L. |
| Height (mm) | 490 |
| Width (mm) | 405 |
| Depth (mm) | 400 |
| Degree of Compression | 85-90% |
| Noise level | <70 dB (A) |
| Pressure | 2250 kg at 8 bar |
| Approvals | CE |
Menu
© 2021 All rights reserved. Mil-tek and the Mil-tek logo are registered trademarks of Mil-tek Danmark A/S.
Want the latest news, insights and expert advice from around the industry? Join the conversation or subscribe to our newsletter.
By submitting a form on this website, you are requesting for Mil-tek to contact you directly. Your personal information will be kept securely and remain private.
Should you wish to opt-out from all future communications, please contact a Mil-tek representative or click here
